Macap M42M Grinder with machine purchase - plus $420
420 520 A$420.00 - A$520.00
- For the packaged price....add this grinder to the 'add to cart' (make sure you have the chosen coffee machine already in the cart).
- To see the packaged price click on the cart (after the grinder has been added).
Then Checkout....and your machine & grinder will be on their way!
*this price is only valid if purchasing a coffee machine at the same time
Macap M42M GrinderMacap was established in Venice (1930). It is a coffee equipment supplier that has a great reputation for producing quality products. All of Macap's grinders are the result of constant refinement in quality and excellence. The Macap M42M is a high performance espresso grinder suitable for the home or office use.
- Measurements: 43 cm H x 19 cm W x 31 cm D).
- Weight: 9 kilograms
- Power: 250watts RPM: 1400. 230 volts, 50/60 hertz.
- Flat grinding blade diameter: 58mm.
- Coffee beans hopper capacity:500 grams
- Body Colour - Black or Chrome
- Stepless grinding regulation
- Tinted Bean Hopper
- Programmable Dose adjustment
- Electronic / On demand grinding
- Dual mode – The Macap M42M can switch between semi-automatic and on demand grinding. On the right side of the grinder, there are 2 switches. The one on the right is the power switch. The one on the left switches between the 2 modes. The “M” position is for semi-automatic grinding. The “T” position is for on demand grinding.
- Programmable – To the right of the coffee chute is the programmable adjustment knob. It adjusts the length of time when grinding on demand. Turning clockwise to a lower number will decrease the grinding time. Turning counterclockwise to a higher number will increase the grinding time.
- Single / Double dosing – Underneath the coffee chute is a red button. This starts the grinding process. When semi-automatic grinding, press and hold until you have the amount of ground coffee desired. When grinding on demand, press once for a single dose or twice for a double dose.
- Stepless – Gives you access to an “infinite” number of grind settings. This allows you really fine tune your grind fineness of your coffee beans. The numbered dial underneath the hopper helps you remember your current grind setting easier.
- Adjustment knob – Located in the rear of the machine just below the hopper. There are 2 knobs on both sides. When using the right knob, turning clockwise will make the grind finer. Turning counterclockwise will make the grind coarser.
- Flat burrs – Large size at 58 mm. The larger the size, the more of a grinding surface, resulting in faster production.
- High rpm – Faster spinning rate at 1400 rpm. The higher the speed, the faster the production, which can increase efficiency and reduce wait times.
- Easy access – Remove the bean hopper. Unscrew the numbered dial and hopper screw. Turn the upper burr holder clockwise until the top assembly comes off. This will give you access to the burrs and the grinding chamber. The burrs themselves are held in with Philips head screws.
- Low profile – The total height of the grinder without the hopper is around 30cm. The bean hopper adds another 13cms bringing the total height to approximately 43cms. The total capacity is approximately 500kg of whole coffee beans.
- Tinted – Helps to avoid pre-mature deterioration of beans from light sources (such as sunlight).
- Set screw – Secures the hopper to the grinder. Serves as a reminder for users from quickly removing the hopper if it is full of beans.
- Finger guard – Prevents users from “accidentally” putting their fingers in the grinding burrs.
- Stopper – A door near the bottom of the hopper can be pushed in to close the opening. This allows you to remove the hopper with beans inside so you can easily change the beans. There will be some beans already passed in the burrs which will have to be ground out first before removing the hopper.
- Ease of use – Accommodates most portafilters. The clearance from the fork to the funnel is approximately 7cms.
- Hands free – Above the fork is a hook that your portafilter can rest on. This allows for practically hands free operation, aside from pushing forward to start the grinding process. The hook is adjustable to fit any size portafilter head. There is an Allen key screw (~2.6 mm) that holds the hook in place.
- Container grinding – The fork is not easily removable. However it does not stick too far out from the grinder (~6cms). Also the coffee chute is wider than other grinders. This makes grinding into a large container no problem.